SPC Plank Collection Manufacturers in Pune

• Install the first plank in the second row by inserting the long side tongue into the groove of the plank in the first row. This is best done with a low angle of the plank. Maintain pressure into the side seam as you rotate the plank to the subfloor.

• Install the second plank in the second row by inserting the short end tongue into the previously installed plank groove. Align the plank so that the long side tongue tip is positioned just over the groove lip of the plank in the first row. Working from the end seam, at a low angle, insert the long tongue into the groove of the adjoining plank. Very little force is required to seat the tongue into the groove. You should feel the tongue lock into the groove.

• Work across the length of the room installing planks along the wall in the first row and then aligning the planks in the second row. It is critical to keep these two rows straight and square, as they are the foundation for the rest of the installation. Check squareness and straightness often.

• Cut the last plank in the first row and leave an expansion gap of around 5/16" (8mm). Planks may be cut with a Utility Knife using the “score and snap” technique. The leftover of this plank may be used to start the third row if it's a minimum 6" (15cm) long.

• Continue installing planks and make sure to achieve a random appearance with end pieces of minimum 6" (15cm). Check that all planks are fully engaged; if a slight gapping is found, the gap can be tapped together by using a tapping block and a scrap of flooring to cover the tapping block in order to avoid damages on the planks.

• The maximum area that can be installed without an expansion joint is 10m × 20m. A section length of approximately longer than 12.5m should be installed with expansion joint. If the temperature while using is higher than the temperature when installing, should apply a little smaller area and shorter length than usual for the standard of expansion joint.

• When fitting under door casings, etc., the flexibility and convenient connection of SPC click becomes evident. If necessary, a flat pull bar may be used to assist in locking the planks.

• When fitting around obstacles or into regular spaces, planks can be cut easily and cleanly using a Utility Knife with a sharp blade. It is often beneficial to make a cardboard template of the area and transfer this pattern to the plank.

• Protect all exposed edges of the flooring by installing wall moulding and/or transition strips. Make sure that no plank will be secured in any way to the subfloor.

• Protect the finished flooring from exposure to direct sunlight.

• AC4 Grade Material
• Waxed Locking
• Quick and Easy to fit
• Easy to reinstall
• Glueless and no mess
• Self-Aligning
• Easy Floor comes in 15 different pleasing designs and shades.
• Size : 1212 x 195 x 8.3mm
• Warranty: Residential – 10 years, Commercial – 2 years

• The predominant cause of damage to a floor's finish is abrasion from dirt and grit. It is important to use walk of mats at entrances and doorways and non-staining floor protectors under heavy furniture, chairs, and tables.

• Use rugs that are made specifically for vinyl floors and shake them out regularly. Place rugs in any area where water is in use, such as sinks or a pet's water dish.

• To prevent the floor from overheating or trapping moisture, never cover the flooring before, during, or after installation with any type of non-breathable or excessively thick rugs, mats, solid surface items, plastics, or a mattress that are laid directly onto the floor. It must be allowed to breathe.

• Oil or petroleum-based products can stain flooring surfaces. Do not track asphalt-driveway sealer, motor oil, wood stains or similar products onto the vinyl floor covering.

• Any flooring may become slippery when wet. Immediately wipe up wet areas from spills and be careful walking on any newly cleaned floor while it is wet.

PET GUIDE

Protecting the beauty of your floor can be easy, even with pets. Follow these simple guidelines to keep your flooring in good condition while having indoor pets.

• Clip your pet's nails regularly. If you can hear the nails clicking on the floor, they need to be trimmed.

• Wipe up any pet waste/vomit as quickly as possible. These accidents, if not properly cleaned up and/or left for long periods of time, are harsh and can damage the finish.

• It is recommended to use natural fiber rugs or a riser to keep water bowls off the floor.

• If your pets are hyper and like to run and slide across the floor, it is recommended to place rugs in these areas to protect the floor.

CLEANING METHODS

• Vacuum (WITHOUT BEATER BRUSH), dry mop, or sweep your floor at least once a week or more if needed. Do not let sand, dirt, or grit build up. It will act like sandpaper, and abrade and dull the finish. The best method of removing dirt and grit is vacuuming with a soft brush attachment on your vacuum.

• After all dirt and grit particles have been removed (using a vacuum, dry mop, or broom) lightly spray a mist of the cleaner over a 4' × 6' area of your floor or directly on the cleaning cloth. Thoroughly clean the floor surface and dry if needed. Finish one area before moving onto the next. Repeat the process until the floor is clean. When the cleaning cloth becomes soiled, rinse with water, thoroughly wringing out the cloth. Once the cleaning cloth becomes excessively soiled, launder and reuse. Excessively soiled cleaning cloths will cause streaking and can abrade the floor.